*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
3700X搭配X570 降壓跑CPU-Z 燒機溫度
不是啥嚴謹測試
只是邊燒機邊用軟體控制,降壓截圖觀察而已 1.4V 1.3V 1.2V 1.1V 1.0V |
|||||||
2019-09-01, 01:50 PM
#1
|
*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
按了電壓變化後,跑分是慢慢變動的,我截圖時沒有等~~
結論 1.35V以上,頻率會碰到溫度牆,降到4GHz以下 1.25V附近是最佳溫度與效能點 原廠散熱器壓不住跑分溫度,順順用倒是沒問題 最佳搭配應該是升級散熱器後用預設電壓 1.0V穩定後截圖 1.25V穩定後截圖 此文章於 2019-09-01 02:11 PM 被 cdx 編輯. |
||
2019-09-01, 02:04 PM
#2
|
Junior Member
加入日期: Jun 2002
文章: 990
|
電壓是如何調的?使用Ryzen Master +PBO? 你這顆1.1-1.2V看來是最佳, 可以多核全速持續. 不過這應該不是預設電壓吧!? 在降下去就其怪的開始效能減少,就便溫度與頻率都上去了。這不知和人說的電壓過低會縮缸有關!?
不過體質差真多...我的R5 3600用1.28V以下4.1G就不穩了, 3700X還可以4.1G 1.2V
__________________
“Suffering is not good for the soul, unless it teaches you how to stop suffering. That is its purpose.” - Seth Speaks: The Eternal Validity of the Soul “Live every day to its fullest, and do not be a slave to your hopes for the future. If you do not learn to enjoy today you will not enjoy the future no matter what it may bring.” - The Seth Material “Desire, wish and expectation rules all actions and are the basis of all realities.” - The Seth Material |
2019-09-01, 02:28 PM
#3
|
*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
引用:
小星星的Dragon_Center_1.0.25.0 電壓低應該是PBO會慢一點啟動,或是啟動的核心數比較少吧~我猜啦 BIOS一樣是昨天設的Offset -0.2V 頻率.PBO等都是自動 記憶體3200Hz C16,這版CPU微碼有問題,所有廠商記憶體超過3400Hz都不穩 上一版可以穩定3600Hz C18 很不嚴儘,防毒.瀏覽器.BT~甚至PotPlayer 都還沒關 此文章於 2019-09-01 02:41 PM 被 cdx 編輯. |
|
2019-09-01, 02:32 PM
#4
|
Junior Member
加入日期: Jun 2002
文章: 990
|
引用:
所以msi的軟體會覆寫掉BIOS那-0.2的offset,變如BIOS裡直接指定固定一樣!?如果這樣說就行得通, 不再讓PBO控制電壓. 如果沒有微星的軟體, 那PBO就會用預設想用的, 然後減掉0.2來跑. 體質差一點的可能就壓降過多效能大減. 我印象中用offset降壓後讓PBO自理, 我的多核只剩3400-3600 你這樣手動設定電壓後, CPU-Z的電壓和頻率還會變化嘛?
__________________
“Suffering is not good for the soul, unless it teaches you how to stop suffering. That is its purpose.” - Seth Speaks: The Eternal Validity of the Soul “Live every day to its fullest, and do not be a slave to your hopes for the future. If you do not learn to enjoy today you will not enjoy the future no matter what it may bring.” - The Seth Material “Desire, wish and expectation rules all actions and are the basis of all realities.” - The Seth Material 此文章於 2019-09-01 02:49 PM 被 moronNZ 編輯. |
|
2019-09-01, 02:46 PM
#5
|
*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
CPU-Z的燒機電壓0.992V,頻率4074~4099Hz
Dragon_Center的燒機電壓0.996V,頻率4076~4101Hz CPU-Z的待機電壓1.V,頻率4074~4099Hz Dragon_Center的燒機電壓0.996V,頻率4076~4101Hz 倒是待機時電壓設定會自己跳回1.25V上下, 燒機時沒有被提升電壓,BIOS會待機時自動補正? 測試關閉Dragon_Center還是會自動修正XD 不確定補正是到安全電壓還是到設定電壓 不怕當機的可以試看看BIOS下降更多電壓~我是懶得試了 BIOS開機不過太麻煩了~還要開機殼清除~我沒裝延長線阿XD 此文章於 2019-09-01 03:15 PM 被 cdx 編輯. |
2019-09-01, 03:07 PM
#6
|
Junior Member
加入日期: Jun 2002
文章: 990
|
我的板子是B450M PRO GAMING
印象中我的BIOS一旦指定了電壓或頻率的乘數, PBO就被關掉, 變手動. CPU-Z此時不管待機或全速, 都顯示最大頻率與指定電壓. 所以才會想問如果你用軟體改, 是否顯示電壓或頻率會隨工作量跳動, 如PBO開啟一樣. 我在找看要如何設定最大電壓, 而不是固定電壓. 現在固定電壓可以讓我跑最多核最高速, 但是此電壓在待機時卻是過高, 會較耗電. 在看看是否是我板子的問題還是大家都如此.
__________________
“Suffering is not good for the soul, unless it teaches you how to stop suffering. That is its purpose.” - Seth Speaks: The Eternal Validity of the Soul “Live every day to its fullest, and do not be a slave to your hopes for the future. If you do not learn to enjoy today you will not enjoy the future no matter what it may bring.” - The Seth Material “Desire, wish and expectation rules all actions and are the basis of all realities.” - The Seth Material |
2019-09-01, 03:23 PM
#7
|
*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
可能跟CPU-Z軟體版本有關吧?
我看電壓.頻率都是會亂跳.... |
2019-09-01, 03:55 PM
#8
|
*停權中*
加入日期: Jul 2001 您的住址: 台中
文章: 3,574
|
結果手癢設Offset -0.25V,不給開機....
BIOS設成固定電壓1.15V,Dragon_Centerg設定1.0V 這樣燒機頻率掉到4100Hz時,電壓就不會往下掉0.992V....而且待機也不會自動跳回1.25V 而是固定在1.008V(CPU-Z) 此文章於 2019-09-01 05:53 PM 被 cdx 編輯. |
2019-09-01, 05:49 PM
#9
|
Junior Member
加入日期: Jun 2002
文章: 990
|
剛剛做了一下測試。沒有Ryzen Master, 只有AMD drivers,只透過BIOS更改。CPU-Z是官網的最新64bit。
PBO開啟,固定電壓1.29v CPUZ 單核/多核 407/3300,電壓顯示固定,頻率跳動。 PBO開啟,電壓自動。 CPUZ 單核/多核 503/4050,電壓跳動,頻率跳動。 PBO開啟,電壓用offset -0.1v。 CPUZ 單核/多核 495/4010,電壓跳動,頻率跳動。 PBO開啟,電壓用offset -0.15v。 CPUZ 單核/多核 405/3320,電壓跳動,頻率跳動。 PBO開啟,電壓用offset -0.2v。 無法開機。 PBO開啟。倍頻41,電壓1.29v。此時PBO應該實際失效。 CPUZ 單核/多核 502/4190,電壓固定,頻率固定在4.1G。 因此我這邊看到的是,電壓或倍頻一旦指定,PBO就怪怪的。如果PBO在運作,那offset降電壓有可能會有降低效能的影響,降過多可能會見到2成的折損。如果電壓讓PBO控制,那在全速時會因電壓過高發熱過高而降速,反而跑不了真正最佳的效能。我是用瓦特計量過,PBO全速自動電壓時多耗了10W來取得較差的效能。此時如果知道自己處理器的體質,可以透過降壓,用較少的功耗還能多3-4%的多核效能。PBO 好處是單核成績能衝比較高,待機的功耗會再稍好些。 如果1.4V那張分數是3700x在PBO全自動的,那核心越多,越要知道處理器最佳電壓,八核那分數的折損可是要10%了(5150->4600),12-16核可能更驚人
__________________
“Suffering is not good for the soul, unless it teaches you how to stop suffering. That is its purpose.” - Seth Speaks: The Eternal Validity of the Soul “Live every day to its fullest, and do not be a slave to your hopes for the future. If you do not learn to enjoy today you will not enjoy the future no matter what it may bring.” - The Seth Material “Desire, wish and expectation rules all actions and are the basis of all realities.” - The Seth Material 此文章於 2019-09-01 06:25 PM 被 moronNZ 編輯. |
2019-09-01, 06:17 PM
#10
|