這就是所謂的挑片
意思是說你可以考慮買台DVD燒錄機了

Hitachi-8X-DVD-ROM 的韌體應該在網路上還找得到,
更新一下,
也許就能解決挑片的問題.

8x以下 DVD ROM 很少可以支援 dvd-R or DVD+R

8x的很舊了~可以換一台16x的
1張小朋友找~很便宜了

hitachi早期的機種比較挑-r
像我benq燒出來的-r就不吃
其他燒的就吃的還可以
不過只能2x讀

+r倒是很正常

是挑片問題喔?那另一個朋友16x的dvd也是挑片問題了?我在試試吧.謝了.各位^-^

Hitachi日立GD-5000 DVD-ROM (8X/40X)最新Firmware 0215版（2001年11月14日新增）
Hitachi日立GD-5000 DVD-ROM (8X/40X)Firmware 0215
http://down.cinews.net/newhtm/403/page_29403.htm
請問高手.我已經找到更新韌體.試了許多次才知道.此程式執行後是會直接解壓縮檔案到小磁片上.看了一下小磁片內容是DOS開機片程式.還有兩個主要檔案flashup.exe與5015G002.DLD.我看了說明方式是要輸入參數A:/>flashup a:/5015G002.DLD 2/a.去執行.但試了很多次都不行更新為0215版.不知道哪裡有出錯.請高手幫幫我吧.3Q!
硬體部分:我裝了2顆硬碟.2台光碟機(一台DVD-ROM.一台CD-ROM)

搭個順風車
請問一下大家
現在要買DVD-ROM
有哪一款可以推薦的
主要的要求是讀片穩定(包含+-R)
做為搭配benq1625的來源
謝謝

System hanging when loading software from the Millennium reference bundle with Hitachi 8x DVD Drive


Issue

When trying to load software from the Millennium reference bundle with Hitachi 8x DVD CD-Rom Drive, the computer may appear to hang.


Solution

1. Leave the floppy disk in the floppy drive, and the computer will restart and come to an A:\> prompt.

2. At the A:\> prompt, type the following -
FLASHUP A:\5015G002.DLD X /A
where X is a number between 0 and 3, representing the Hitachi 8x DVD CD-Rom drive's position on the Hard Drive controller.

Controller ID Position
Primary IDE Master 0
Primary IDE Slave 1
Secondary IDE Master 2
Secondary IDE Slave 3


If you are unsure as to which position the DVD CD-Rom drive is on the Hard Drive controller, follow these steps

3. Restart the computer and at the initial Gateway logo, press the F1 key on the keyboard to enter the BIOS.

4. When the blue BIOS screen appears use the right arrow key on the keyboard to go to the Advanced screen.

5. On the Advance Screen will be an option IDE Configuration.

6. Highlight this by using the down arrow and once highlighted, press enter.
The information displayed will be similar to the following ?

Controller ID Device Position
Primary IDE Master WDC AC 22100 H 0
Primary IDE Slave [None] 1
Secondary IDE Master Hitachi DVD ROM GD 5000 2
Secondary IDE Slave [None] 3

More Information

If after executing the command above, the following error appears ?
No Hitachi Drives Detected
this means the incorrect Hard Drive controller number was entered.

Repeat steps 3 to 6 above to check the position of the Hitachi DVD Rom drive on the Hard Drive controller.

Once the correct position has been noted, repeat steps 1 and 2 above.