|
||
|
Power Member
 加入日期: Jul 2004
文章: 595
|
給oScARSr大:接續官版Forceware和我家FX5600U的超頻問題
接續http://www.pcdvd.com.tw/showthread....06&page=5&pp=10
近日在guru3d翻到這兩篇文章: http://forums.guru3d.com/showthread.php?threadid=104997 http://forums.guru3d.com/showthread...10&pagenumber=1 都是提我這張顯卡的問題，也完全符合我們的超頻問題 由於小弟英文水平有限(目前就讀國二)，只能用dr.eye加減著看 好像是換別的bios就解決了，不知有哪位好心人能幫忙翻譯+找出解決之道  |
|||||||
2004-09-10, 09:16 PM
#1
|
|
|
Major Member
加入日期: Jun 2003 您的住址: where the light is
文章: 271
|
大致是這樣子吧
把你的顯示卡bios用nvflash讀出來 然後用hex editor 開啟 搜尋代表時脈的位置 例如目前核心是425MHz就是 A6 04 (42500的16進位) 記憶體500(也就是250 DDR) 就是 61 A8 (25000) 然後把搜尋到的地方都用你想超到的時脈代替 接下來用 Bios Editor 開啟再存檔 (目的是為了更新checksum) 然後用NVFlash燒回顯示卡就好了 最後我要說的是....顯示卡壞掉別來找我 我只是負責翻譯而已  |
||
|
2004-09-10, 11:27 PM
#2
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
這樣每超一次都要更新一次??
除此之外難道沒別的方法嗎?... |
|
2004-09-11, 12:06 PM
#3
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
推一下^^
看來我真是天殺的買錯衰卡了 開始覺得不了解電腦的人多幸福..... 看著我同學用1.2g+tnt2+128 ram玩的多高興，一點煩惱都沒有XD"" |
|
2004-09-11, 10:32 PM
#4
|
|
|
Power Member
加入日期: Feb 2003 您的住址: 愛情的盡頭
文章: 538
|
更新修改過的Bios後,卡就永遠照那個頻率跑了........
不需要每超一次都要更新一次...... |
|
2004-09-11, 11:14 PM
#5
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
我的意思是從bios更改頻率太危險了，萬一卡掛了就慘囉
為什麼我這麼衰- -|||.. |
|
2004-09-12, 12:31 PM
#6
|
|
|
*停權中*
加入日期: Apr 2004 您的住址: 悪滅
文章: 4,257
|
我看的翻譯和上面的網友不一樣，
他只是更新BIOS，並沒有改什麼HEX檔 OC的問題就解決了。 此文章於 2004-09-12 01:53 PM 被 oScARSr 編輯. |
|
2004-09-12, 01:50 PM
#7
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
去哪更新@@?
可以的話幫忙一下，我沒任何經驗.. |
|
2004-09-12, 02:46 PM
#8
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
Please read other threads on how to backup your original BIOS and how to flash BIOS'es. I did a lot of reading/research before I attempted this procedure. This is my very first time I actually did this kind of thing to my video card. In other words, I'm a n00b when it comes to this.
I found the Jaton Corp. FX5700NU BIOS in the following website: http://www.station-drivers.com/page/vgabios.htm Look under NVIDIA Geforce 5700 4.36.20.35.15 Jaton Note that this is a zip file of an executable. The executable actually makes a boot disk for you; so you need an empty floppy disk. I did not use the boot disk, however. All I did was just copy the file p191-0n.rom and saved it to my own boot disk. I mentioned this earlier but I will say it again anyway: make a backup copy of your original BIOS first, then try to flash the Jaton BIOS (please don't take this advise as an insult, I just don't want you to damage your video if something goes wrong with the flashing procedure. I've read in other threads and in other forums where others did not backup their BIOS and the BIOS procedure went wrong!!!). I used nvflash ver. 4.42 using the followng parameters in DOS mode: nvflash -b backup.rom - to back up the original BIOS nvflash -p -u -f p191-0n.rom - to flash my card with the Jaton BIOS I hope this helps.... You can also check out the following link as well: http://forums.guru3d.com/showthread...threadid=105802 -- 意思好像是去http://www.station-drivers.com/page/vgabios.htm 找nvidia的bios，這點我有找到 至於怎麼更新，就不知道了- -|||... |
|
2004-09-12, 03:09 PM
#9
|
|
|
Power Member
加入日期: Jul 2004
文章: 595
|
冒著被老爸K死刷壞的風險下..........去嚐試了
目前還活著回來，問題應該是解決囉 時脈反而可以超的更高，以前485，580就上不去了，現在可以到510，601耶^^".. |
|
2004-09-12, 06:55 PM
#10
|
|
