|
||
|
Major Member
 加入日期: Apr 2004 您的住址: 家里
文章: 108
|
哇!! Benq DDW-1640 BSRB老是燒�***
這幾天開始, 用我心愛的小Q 1640燒片子, 大都是燒映像檔,
突然發現常常會燒�***, 開始就停住約3分後吐出, 不論是infomedia or Retik 都一樣ㄋ = =" 怎會這樣 @@" 剛剛用Nero CD-DVD Speed 4.51.1 測試 Infomedia R20 碟片 出現: 錯誤:- power calibration area is full (037302) 像這種問題不知道各位有沒碰過或建議該做如何處置?? 系統已重新安裝過 = =" 還是一樣的狀況 @@" |
|||||||
2006-07-29, 08:55 AM
#1
|
|
|
Master Member
  加入日期: Jul 2004
文章: 2,429
|
那你就換回舊版韌體吧
不是新的就最好 不過通常這個訊息是告訴你要換一台新的....不然就自己調功率 |
||
|
2006-07-29, 09:15 AM
#2
|
|
|
Basic Member
加入日期: Apr 2005
文章: 11
|
基本上如果你使用的DVD碟片他已經可以認到，一般是不太需要更新韌體了，要更新韌體除非買到的DVD碟片認不到(一般現在是要燒DL跟16X的碟片才會要去更新)4X跟8X以目前的碟機廠商幾乎可以說是不在做調整囉，當然越舊款的碟機越不可能調。所以建議你改回舊的韌體，適合你目前用到的碟片的韌體就可以了，不需要在一昧的求新。
|
|
2006-07-29, 09:30 AM
#3
|
|
|
*停權中*
加入日期: Mar 2002
文章: 385
|
引用:
錯誤:- power calibration area is full (037302) 好熟悉的文字...前幾天才第一次看過... 不過我似乎是光碟片的問題啦..... 當然我也是1640....也有可能我們的機子操太凶...1640有老化的跡象?? http://www.pcdvd.com.tw/showthread.php?t=640055 |
|
|
2006-07-29, 09:43 AM
#4
|
|
|
*停權中*
加入日期: Mar 2002
文章: 385
|
引用:
你講的應該是不同的問題....... 你說的是調整雷射最大功率都還不足以正常燒錄... 而發問者的問題是....無法得到穩定的燒錄校正...以至於都把碟片上的"power calibration area"都用完..... |
|
|
2006-07-29, 09:52 AM
#5
|
|
|
*停權中*
加入日期: Mar 2002
文章: 385
|
From Nero website:
http://ww2.nero.com/enu/FAQs_Produc...Messages.html#9 9. I get a 'Power calibration error' or 'Calibration area (almost) full' error message. Why? Power Calibration is controlled by the recorder. Before any write operation, all recorders must do a 15 step power test to determine the optimum power for writing to the CD; this is called "Optimum Power Calibration"(OPC). During the write, it continues to do this test to get the best write throughout the whole CD; this is called "Running Optimum Power Calibration" (ROPC). This whole process is controlled by the recorder, though initiated by programs such as Nero. There is an area on the inner part of the CD for the test and test data info to be stored. You can use this area up to 999 times. If you receive the "Power calibration error" or "Power calibration area is (amost) full" error message, the cause will be either poor media, poor power, or a defective recorder. Please try the following solutions: Update the firmware of your recorder. Please check the manufacturer's website for the latest version. Try another brand of CD-R or CD-RW media. Try different power connectors, and for recorders, do not share power with other devices. It needs its own power connector. If the error occurs with an external recorder, the power source in the chassis could be the cause. As a test, try to take the recorder out of the external chassis and connect it internal. Try different configurations, such as taking the CD-ROM to the primary IDE bus as slave and have only the recorder connected to the secondary IDE bus as master. Send the recorder in for service. |
|
2006-07-29, 10:59 AM
#6
|
|
|
Major Member
加入日期: Apr 2004 您的住址: 家里
文章: 108
|
3Q for 大家的協助!!
果然問題出在 Update the firmware of your recorder. Please check the manufacturer's website for the latest version. 但是不是最新的, 反而是用BSPB(OK), BSQB(NG), BSRB(NG) 難道是因為年紀大了(機子)所以不能用新的韌體 >"< (謎之音:年紀大了就不要用太刺激的 = =") |
|
2006-07-29, 11:08 AM
#7
|
|
|
*停權中*
加入日期: Mar 2002
文章: 385
|
引用:
你更新FW後才出問題嗎? 如果不是....加上你提到"不論是infomedia or Retik都一樣"....那你應該考慮Power或燒錄機的問題了....或許更新韌體只是讓機子剛好可用臨界點上而已... |
|
|
2006-07-29, 11:24 AM
#8
|
|
|
Major Member
加入日期: Apr 2004 您的住址: 家里
文章: 108
|
引用:
嗯...原本燒的好好的, 但你知道人ㄚ...總是喜新厭舊(希望不要給我老婆看到 ^^") 所以就興致勃勃的把網路上某位大大分享的最新版韌體(我不是說那個有問題!!) 把我的DDW-1640(小Q)給升級了!! 後面就發生了上面的事情 = =" 換回舊的到目前為止都OK ^^ (今天8/4??) |
|
|
2006-08-04, 08:15 AM
#9
|
|
|
Major Member
加入日期: Apr 2002 您的住址: 家楊梅住新莊
文章: 237
|
我是二月機
前天 燒錄約 10片吧 結果 突然死掉 完全無法讀取任何片 更新為舊的或是更新的 也不行 只好送修了 |
|
2006-08-04, 10:36 AM
#10
|
|
