I get the following error when playing Half-Life 2 'The Instruction at 0x####### referenced memory at 0x#######. The memory could not be 'read"
這段不必翻譯吧...出現0xxxxx不能讀取....
To help isolate the cause for your specific error, please do the following steps:
1,2,3不翻譯了,應該看的懂像更新driver,dx9c....等

4. Page file: try turning off your system paging file (you have to reboot) and setting your page file for 1x to 2x your physical system memory. Find this in your control panel > system > advanced > performance > advanced > "virtual Memory".
分頁檔...試著關掉分頁檔(會要你重開機).設定分頁檔大小為你主記憶體的1-2倍.
(Why??不懂...)
5. Make sure that you are NOT overclocking any components in your computer.

6. Make sure you do not have an overheating problem on your computer.

確定你的電腦沒有超頻還有過熱的問題(2段一起翻)
7. If you have an language other then English set for your Operating System, make sure that you are not setting the console key to an invalid character (§ for example is not valid).
如你的系統有"英文"以外的設定,確認不是設定操作的按鍵為無效的字元.

8. If you are using ANY refresh-rate forcing program, please disable or uninstall it.
如有使用任何強迫性更新頻率程式,請移除或關掉.(what is "ANY refresh-rate forcing program"???I don't understand.疑問中....)

9. If you have any 3rd party Codecs installed, please temporarily uninstall them.
若有第3協力廠商的編碼程式安裝,請暫時移除.
10. If you have an ATI Graphics card, please uninstall ATI-ACE, ATI-SMART, Trueform and Catalyst AI, also disable VPU Recover if that causes you problems (but remember it's being triggered by some sort of problem!)
若使用ati顯示卡,請移除ati-ace,ati-smart,Catalyst AI(本人沒使用ati顯示卡不知這是什麼).若還是有問題也關掉vpu recover.(但記得那麼些問題發生...)這段不知翻的正不正確?
11. Disable all IM programs and do not alt-tab to your desktop, swapping the game out may trigger this problem
關閉所有IM程式(網路管理程式???)還有不可用alt+tab跳回桌面,這將會發生此問題.

12. Verify your game caches and defrag your computer disk(s).
確認你的快取跟重組你的磁碟

13. and of course run a good memory test:
Here are a few you can get for free:
Windows Memory Diagnostic Download Page
Memtest86
Simmtester DocMeM Memory Test Program
以下測試是否通過(這些都市ram的測試程式,不用我說了吧,memtest86...等,乾脆我覺得prime95也測一下好了)

14. Put this CVAR in your HL2 launch properties and see if it helps:
-window +mat_forcehardwaresync 0
在hl2潔徑後加入那個指令
15. If you are using two memory or more memory modules, try running with only one module and see if you still have this problem. Reducing the number of modules will effectively speed up your memory timing. If the game runs ok with one module but not two, then you have a motherboard timing problem and you will need to make some changes, READ YOUR MOTHERBOARD MANUAL.
若你裝2條以上的ram,試著只裝一條能否解決問題.減少記憶體條數可有效提升記憶體時序.
若裝1條ok但2條不行,你有主機版時序設定的問題,須要做一些設定值的改變,參考主機版手冊.
a. Relax the memory timing some motherboards have "conservative" timing or you can manually increase CAS and increase prefetch. If CAS is set to 2.0 increase it to 2.5. If Prefetch is set to 6, increase it to 7 or higher (up to 11).
放寬記憶體調整在有些mb上有conservative" timing,或你可手動增加cas跟prefetch值
若cas設定為2.0增加至2.5.Prefetch設定為6,增加至7以上(最高到11)
b. Slightly increase the memory core voltage if your motherboard supports this option, consult your motherboard manual. Raising the voltage will effectively speed up the memory, but will also increase the heat.
若你的主機版支援調整記憶體電壓,微量增加ram核心電壓,請參考主機版手冊.提高電壓有效的提升速度,但發熱量也會增加.
(這2段應該是叫我們調高cl,cas,增加電壓...等,我是覺得調整後還是要測p95與memtest86...等)
以下的就不講了,叫你將系統資訊送到value...
本人英文程度不是很好,翻的怪怪的,還請各位大大指正本人的錯誤.
來源:http://steampowered.custhelp.com/cg...&p_sp=undefined