[求助]雙網路設定的問題?
 

[求助]雙網路設定的問題?

我的電腦有兩張網卡,一張接HINET ADSL固接式,另一張接HP 7410多功能事務機,這兩張網卡的IP,子網路遮罩,預設閘道都不同,
但當我設定兩張網卡的預設閘道不同的時候,所有的網路就不通了,但當我把其中一張網卡的預設閘道給拿掉之後,網路隨即就恢
復正常了!

現在我該如何解決此問題? 請高手們幫幫忙,謝謝!

http://www.vlab.com.tw/vlabforums/v...1be534371b42d4a

另外，建議用雙網卡+route or 雙網卡 + 設定去google，你會找到許多資料

你不是已然解決了嗎?

如果接HP 7410多功能事務機的 那張網路卡 是直接接 並沒有其它 內部網段網段
就只要 把 接HP 7410多功能事務機的 那張網路卡 的 預設閘道 做 不要設定 就好了阿

問題連HP 9410的那張網卡,如果沒設 預設閘道 的話,HP 9410 DRIVER連線不是會很慢嗎? 有時甚至會發生連不上等情況啊! 沒有人遇過此情況嗎? 尤其當另一張網卡連線的是 廣域INTERNET 的時候,光是安裝DRIVER 就不知道要搜尋多久才能找到HP 9410?

找台P3等級的舊電腦架BrazilFW,或者用VM/VPC等的虛擬化軟體架設也行

這樣就能解決你的問題了...

Default gateway 只能有一個 :P
話說.................
接HP 7410的網路卡,應該不需要設gateway吧?
HP7410...這台?
http://h50013.www5.hp.com/product/officejet/Q5569A/
HP7410的有線網路部份,應該是設定IP給它或自己有內定IP吧??
http://h10025.www1.hp.com/ewfrf/wc/...le=3597&lang=en
參考一下HP的設定方式吧
透過TCP/IP的方式去連,應該不需要加gateway.

我知道有一套付費軟體應該可以達成
軟體名稱為"IPSwitchRouter",希望對你有幫助

我今天下午搜尋網路,我從 YAHOO 找到最簡單且有用的解決方法了!

=============================================================
Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters]
"IPEnableRouter"=dword:00000001


; 在每張 NIC 之下都要新增 "IPEnableRouter"=dword:00000001 這個設定值,NIC 才會自動 IP Router.
; [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Adapters]
;
; Resolved Question » IP Routing table?
; I have 2 LAN, one is 10.0.0.0 which connect to broadband modem and the other is 172.16.0.0 which
; connect to local network. I like to put a PC with windows 2000 server to act as router that route
; Internet request from 172.16.0.0 to 10.0.0.0, what modification should I add to routing table?
;
; Best Answer - Chosen by Voters
; I'm trying to make sure I understand the physical connectivity from your description,
; so you have a broadband modem and your LAN side has a 10.0.0.0 address, and you also
; have another LAN using 172.16.0.0 addressing, and you want to connect these two together.
; There are multiple ways to accomplish this, but if you want to use a Windows 2000 server
; like you said, you can simply install 2 network interface cards in the machine and connect
; each one to your two networks. Then you must enable IP forwarding. Use the registry editor
; regedt32.exe and drill down to HKEY_LOCAL_MACHINE, SYSTEM, CurrentControlSet, Services,
; Tcpip, Parameters and modify the IPEnableRouter key to have a value of 1 instead of 0.
; You may also be able to check an option box to enable IP routing under advanced network and
; TCP/IP properties instead of using the registry editor. The Win2000 "router" machine will
; now know about both networks, and the machines on your 10 and 172.16 networks will point to
; the Win2K server PC as their default gateway. Or (I think this might be what you're after)
; the 172.16 machines point to the Win2K server PC as their default gateway, and the Win2K
; server PC points out to the broadband router as it's default gateway. Depending on your setup,
; you may need to put a static route in the broadband router for the 172.16 net with a next hop
; of the 10 interface on the Win2K server PC.
==========================================================

原文出處轉貼:
http://au.answers.yahoo.com/questio...d=1006051024871

我剛才連上去看了一下,他都有設GATEWAY呀! 誰說不用的?
而且我記得以前有一次我沒設GATEWAY,INTERNET 也沒 OFFLINE,結果安裝程式搜尋9410搜尋了十分鐘還在搜,如果我把INTERNET 給 OFFLINE 之後,9410不用20秒就找到了! 當時連9410的 NIC 就是沒設 GATEWAY !

嗯..到底是9410還是7410...............雖然這不是重點 XD
Default gateway,連線時只能有一個
你同時兩個gateway當然會找不到- -
安裝軟體搜尋時,實體IP對外線路當然建議是先斷線啊
但是裝完後,不需要每次使用時都要搜尋吧??(不好意思,我沒用過,真的不知道..)

last
希望你知道你引的那篇Yahoo文章是在講啥.