跑prime95錯誤參數代表的意義
 

以前有看過一篇文章,上面有跑PRIME95有錯誤,參數代表的意義(如外頻太高,CPU過熱,記憶體超過頭等等參數),誰能幫我找一下阿

我也想知道
我測試都會出現


cl2 3 2 5

Prime95 23.7 readme.txt...

##################################################
POSSIBLE HARDWARE FAILURE
-------------------------

If the message "Possible hardware failure, consult the readme file."
appears in the results.txt file, then prime95's error-checking has
detected a problem. After waiting 5 minutes, the program will continue
testing from the last save file.

Could it be a software problem? If the error is ILLEGAL SUMOUT and you are
running Windows 95/98/Me, then there is some chance that this is a software
problem. A device driver or VxD may not be saving and restoring FPU state
correctly. Windows NT/2000/XP protects prime95 from bad device drivers.
In that case ILLEGAL SUMOUT is very likely a true hardware error. The good news
is that prime95 recovers very well from ILLEGAL SUMOUT errors. Try seeing
if the problem occurs only when a specific device is active or a specific
program is running.

The other two errors messages, SUMINP != SUMOUT and ROUND OFF > 0.40 are
caused by one of two things:
1) For reasons too complicated to go into here, the program's error
checking is not perfect. Some errors can be missed and some correct
results flagged as an error. If you get the message "Disregard last
error..." upon continuing from the last save file, then you may have
found the rare case where a good result was flagged as an error.
2) A true hardware error.

If you do not get the "Disregard last error..." message or this happens
more than once, then your machine is a good candidate for a torture test.
See the stress.txt file for more information.

Running the program on a computer with hardware problems may produce
incorrect results. This won't hurt the GIMPS project since all results
will be double-checked. However, you could be wasting your CPU time.
If you are getting several errors during each primality test, then I
recommend using your machine to factor Mersenne numbers or run less
strenuous distributed computing projects at
http://www.mersenne.org/projects.htm.

##################################################

您試試看CL2.0-3-3-5,或是CL2.0-3-2-6看看好嗎

CL2.0-3-3-5
可以測試了
哇~那我這記憶體體質差唷
我才跑266而已...我又沒超頻

不一定,A7N8X對RAM參數設定上比較龜毛,
您試試看把CPU設成200*7.5,然後RAM跑DDR400 CL2.0-3-3-5,接著跑Prime95 23.7.1版的In-Place Large FFTs試試看,若是可以過24小時(期間請讓Prime95專心跑),接著可以試試看CPU跑200*8,200*8.5........,這樣超上去,以CPU不加壓,RAM最高設2.7V(我也不喜歡加壓,都設2.6V),相信整體效能會提高許多
PS:若是CPU倍頻有鎖,那就沒辦法了

我怕我的apone的ACK7L會沒辦法撐的住CPU的熱量
上次有上過200*10但是那科風散是比較吵的
我換成ACK7L就再條一次,結果BIOS掛了...(還要重新寫入一次)
那時還好可以進WINDOWS如果不能進那我就不會重DOS寫入了
害我以為要送修了!!

我也是用A7N8X的主機板
很奇怪CL2.3.3.11都可以跑完Super pi 32m
不過一跑Prime95 跑一小時就出錯
後來調成CL 3.3.3.11就可以穩跑24HR了
Prime95要求比較高吧~
bn. 2.5+ oc 3.2+ 1.65v
創見 ddr 1g (茂矽)

你可以試試看跑DDR400 CL2.5-3-3-8 2.6V,應該就能過Prime95 24小時,茂矽的顆粒可能是舊的那一批,SPD CL3.0那一批,要跑CL2.0太難了