那款還有加散熱片勒！
不知道可不可以超頻
用起來爽度應該是100％
但價格似乎太高了

現在新的MB的LAN不是都跑PCI-E x1嗎?

高價板(指NT$3-4000起跳者)有可能是外加PCI-E GbE或南橋內建MAC加外接PHY(尤其是N牌chipset者,不過以鵝個人觀點N牌南橋內建的MAC實在有點讓人搖頭:ase),低價板(NT$3000以下)通常是南橋內建MAC加外接PHY或接在33MHz PCI32上:stupefy: ....BTW,鵝來貼個linux下的測試結果好了,測試環境是以約2m的CAT5e直接對接,client是S754的Sempron2500+1GB DDR400+PCI-E 88E8053,server是AM2的Sempron3000+2GB DDRII667+MCP51內建的GbE(PHY也是Marvell的),沒開Jumbo Frame(因為linux不知為何沒辦法開off loading及Jumbo Frame等功能:ase)....

只開一個connection,88E8053 default有開off loading時....

root@lab01:~# ethtool -k eth0
Offload parameters for eth0:
rx-checksumming: on
tx-checksumming: on
scatter-gather: on
tcp segmentation offload: on
root@lab01:~# time iperf -c 192.168.1.115
------------------------------------------------------------
Client connecting to 192.168.1.115, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 5] local 192.168.1.110 port 56285 connected with 192.168.1.115 port 5001
[ 5] 0.0-10.0 sec 1.09 GBytes 938 Mbits/sec

real 0m10.035s
user 0m0.064s
sys 0m2.008s

throughput約938Mbps,CPU loading約20%....

同上,關閉所有off loading....

root@lab01:~# ethtool -k eth0
Offload parameters for eth0:
rx-checksumming: off
tx-checksumming: off
scatter-gather: off
tcp segmentation offload: off
root@lab01:~# time iperf -c 192.168.1.115
------------------------------------------------------------
Client connecting to 192.168.1.115, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 5] local 192.168.1.110 port 56286 connected with 192.168.1.115 port 5001
[ 5] 0.0-10.0 sec 998 MBytes 837 Mbits/sec

real 0m10.020s
user 0m0.044s
sys 0m3.308s

throughput下降約10%,CPU loading由20%上升到33%(約60%:eek: )....

重新打開所有off loading,開10個connection....

root@lab01:~# ethtool -k eth0
Offload parameters for eth0:
rx-checksumming: on
tx-checksumming: on
scatter-gather: on
tcp segmentation offload: on
root@lab01:~# time iperf -c 192.168.1.115 -P10
------------------------------------------------------------
Client connecting to 192.168.1.115, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 5] local 192.168.1.110 port 36511 connected with 192.168.1.115 port 5001
[ 6] local 192.168.1.110 port 36512 connected with 192.168.1.115 port 5001
[ 7] local 192.168.1.110 port 36513 connected with 192.168.1.115 port 5001
[ 8] local 192.168.1.110 port 36514 connected with 192.168.1.115 port 5001
[ 9] local 192.168.1.110 port 36515 connected with 192.168.1.115 port 5001
[ 14] local 192.168.1.110 port 36520 connected with 192.168.1.115 port 5001
[ 10] local 192.168.1.110 port 36516 connected with 192.168.1.115 port 5001
[ 11] local 192.168.1.110 port 36517 connected with 192.168.1.115 port 5001
[ 12] local 192.168.1.110 port 36518 connected with 192.168.1.115 port 5001
[ 13] local 192.168.1.110 port 36519 connected with 192.168.1.115 port 5001
[ 5] 0.0-10.0 sec 113 MBytes 94.8 Mbits/sec
[ 6] 0.0-10.0 sec 113 MBytes 94.7 Mbits/sec
[ 7] 0.0-10.0 sec 113 MBytes 94.7 Mbits/sec
[ 9] 0.0-10.0 sec 112 MBytes 94.3 Mbits/sec
[ 10] 0.0-10.0 sec 112 MBytes 93.7 Mbits/sec
[ 8] 0.0-10.0 sec 113 MBytes 94.6 Mbits/sec
[ 14] 0.0-10.0 sec 112 MBytes 94.0 Mbits/sec
[ 11] 0.0-10.0 sec 112 MBytes 93.9 Mbits/sec
[ 13] 0.0-10.0 sec 112 MBytes 93.8 Mbits/sec
[ 12] 0.0-10.0 sec 112 MBytes 93.8 Mbits/sec
[SUM] 0.0-10.0 sec 1.10 GBytes 939 Mbits/sec

real 0m10.086s
user 0m0.080s
sys 0m2.044s

CPU loading及throughput都與開一個connection時約略相當....

同上,關閉所有off loading....

root@lab01:~# ethtool -k eth0
Offload parameters for eth0:
rx-checksumming: off
tx-checksumming: off
scatter-gather: off
tcp segmentation offload: off
root@lab01:~# time iperf -c 192.168.1.115 -P10
------------------------------------------------------------
Client connecting to 192.168.1.115, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 14] local 192.168.1.110 port 58168 connected with 192.168.1.115 port 5001
[ 5] local 192.168.1.110 port 58159 connected with 192.168.1.115 port 5001
[ 6] local 192.168.1.110 port 58160 connected with 192.168.1.115 port 5001
[ 7] local 192.168.1.110 port 58161 connected with 192.168.1.115 port 5001
[ 8] local 192.168.1.110 port 58162 connected with 192.168.1.115 port 5001
[ 9] local 192.168.1.110 port 58163 connected with 192.168.1.115 port 5001
[ 10] local 192.168.1.110 port 58164 connected with 192.168.1.115 port 5001
[ 11] local 192.168.1.110 port 58165 connected with 192.168.1.115 port 5001
[ 12] local 192.168.1.110 port 58166 connected with 192.168.1.115 port 5001
[ 13] local 192.168.1.110 port 58167 connected with 192.168.1.115 port 5001
[ 6] 0.0- 7.0 sec 71.8 MBytes 86.0 Mbits/sec
[ 9] 0.0- 7.0 sec 71.3 MBytes 85.4 Mbits/sec
[ 11] 0.0- 7.0 sec 69.8 MBytes 83.7 Mbits/sec
[ 12] 0.0- 7.0 sec 69.8 MBytes 83.6 Mbits/sec
[ 5] 0.0- 7.0 sec 71.5 MBytes 85.6 Mbits/sec
[ 7] 0.0- 7.0 sec 71.7 MBytes 85.8 Mbits/sec
[ 8] 0.0- 7.0 sec 70.2 MBytes 83.9 Mbits/sec
[ 10] 0.0- 7.0 sec 71.5 MBytes 85.5 Mbits/sec
[ 13] 0.0- 7.0 sec 71.1 MBytes 85.1 Mbits/sec
[ 14] 0.0-10.0 sec 372 MBytes 312 Mbits/sec
[SUM] 0.0-10.0 sec 1010 MBytes 847 Mbits/sec

real 0m13.027s
user 0m0.068s
sys 0m3.960s

throughput約略與只開一個connection關off loading時相當,CPU loading由33%上升至40%(約20%)....

總結看來還不錯---吃CPU沒想像中的兇就是了:p:p....

是的，是利用它的頻寬

目前找的到PCI-Express x1 or x4 的 Gigabit Network Adapter 大概就

01.Intel® PRO/1000 PT Desktop Adapter
02.玄人志向 GBE-PCIe
03.D-Link DGE-560T
04.SysKonnect SK-9E21 10/100/1000Base-T Server Adapter
05.SysKonnect SK-9E22 10/100/1000Base-T Dual Port Server Adapter
06.SysKonnect SK-9E81 1000Base-SX Server Adapter
07.SysKonnect SK-9E82 1000Base-SX Dual Port Server Adapter
08.SysKonnect SK-9E91 1000Base-LX Server Adapter
09.SysKonnect SK-9E92 1000Base-LX Dual Port Server Adapter

其他請補充

很好奇的問一下
現在有用GbE網卡的網友
大多是在那些環境下呢!?
公司!?宿舍!?還是家裡!?

除了極少數有幸用100Base以上速率上Internet者以外,大部份人通常還是用在自file server(i.e.動物機:laugh: )上拉檔時提升爽度吧:laugh: ....不過鵝不玩動物機之類的遊戲,純粹是拿來當兜server farm用的樣板而已:ase:ase....

因為主機板的PCI愈來愈少...

而PCI又要用其他重要的介面卡要使用時

所以有需要另外插網路卡的人可以尋求此方式，簡單的說就是物盡其用吧

PCI-Express 的產品還是太少