對不起沒把配備說清楚.....
CPU：雷鳥1G （無超頻）
主機板：華碩A7V133 BIOS:1004版
記憶體：勝創PC150 外頻（無超頻）
顯示卡：愛爾沙 MX （無超頻）
網路卡：Dlink 530TX
電視卡：登昌恆UPG 502TV 版

噁...
我想你應該是電腦高手ㄌ!一次要安裝五ㄍ作業系統!
厲害厲害!!
我頂多安裝二ㄍ作業系統共存,就很夠用ㄌ!!
改天哪ㄍ系統出錯,我看你整顆硬碟也幾乎會完蛋ㄉ!
裝ㄍ2000跟linux 就差不多ㄌ

教你一ㄍ方法買五顆硬碟再加五ㄍ抽取盒好方便ㄚ.嘻嘻
(當我沒說)

平生進退如飆風 一睨人才天下空 獨向蒼天橫冷劍 何必生我慚英雄


[這篇文章曾被 Tony lee 重新修正編輯過 (時間 05-03-2001).]

我強烈建議用: System Commander

看看吧: http://www.v-com.com/product/sc2_ind.html

個人覺得這是最好的多重開機管理軟體

------------------
Who is ashuro?
(A) (S)tupid (H)ome-theater (U)ser (R)eally (O)ccupied

希望以下的資料對您有幫助,在微軟的資料中顯示:

Stop 0x00000050 or PAGE_FAULT_IN_NONPAGED_AREA
This Stop message, also known as Stop 0x50, occurs when requested data is not found in memory. The system generates a fault, which normally indicates that the system looks for data in the paging file. In this circumstance, however, the missing data is identified as being located within an area of memory that cannot be read to disk. The system faults, but cannot find, the data and is unable to recover. Faulty hardware, a buggy system service, antivirus software, and a corrupted NTFS volume can all generate this type of error.

Interpreting the Message
========================
The four parameters listed in the message are defined in order of appearance as follows:

1. Virtual address which caused the fault
2. Type of access (0 = read operation, 1 = write operation)
3. If not zero, the instruction address which referenced the address in parameter 1
4. Opaque information about the stop, interpreted by the kernel

Resolving the Problem
=====================
Faulty hardware. Stop 0x50 usually occurs after the installation of faulty hardware or in the event of failure of installed hardware (usually related to defective RAM, be it main memory, L2 RAM cache, or video RAM). If hardware has been added to the system recently, remove it to see if the error recurs. If existing hardware has failed, remove or replace the faulty component. You should run hardware diagnostics supplied by the system manufacturer. For details on these procedures, see the owner's manual for your computer.

Buggy system service. Often, the installation of a buggy system service is a culprit. Disable the service and confirm that this resolves the error. If so, contact the manufacturer of the system service about a possible update. If the error occurs during system startup, restart your computer, and press F8 at the character-mode screen that displays the prompt "For troubleshooting and advanced startup options for Windows 2000, press F8." At the resulting Windows 2000 Advanced Options menu, choose the Last Known Good Configuration option. This option is most effective when only one driver or service is added at a time.


Antivirus software. Antivirus software can also trigger this error. Disable the program and confirm that this resolves the error. If it does, contact the manufacturer of the program about a possible update.

Corrupted NTFS volume. A corrupted NTFS volume can also generate this error. Run Chkdsk /f /r to detect and repair disk errors. You must restart the system before the disk scan begins on a system partition. If you cannot start the system due to the error, use the Recovery Console and run Chkdsk /r. For more information about the Recovery Console, see chapter "Repair, Recovery, and Restore" in this book. If the hard disk is SCSI, check for problems between the SCSI controller and the disk.

Warning If your system partition is formatted with the FAT16 file system, the long file names used by Windows 2000 can be damaged if Scandisk or another MS-DOS-based hard disk tool is used to verify the integrity of your hard disk from an MS-DOS prompt. (An MS-DOS prompt is typically derived from an MS-DOS startup disk or from starting MS-DOS on a multiboot system.) Always use the Windows 2000 version of Chkdsk on Windows 2000 disks.

Finally, check the System Log in Event Viewer for additional error messages that might help pinpoint the device or driver that is causing the error. Disabling memory caching of the BIOS might also resolve this error.

Microsoft periodically releases a package of product improvements and problem resolutions for Windows 2000 called a Service Pack. Because many problems are resolved by installing the latest Service Pack, it is recommended that all users install them as they become available. To check which Service Pack, if any, is installed on your system, click Start, click Run, type winver, and then press ENTER. The About Windows 2000 dialog box displays the Windows version number and the version number of the Service Pack, if one has been installed.

Occasionally, remedies to specific problems are developed after the release of a Service Pack. These remedies are called hotfixes. Microsoft does not recommend that you install a post-Service Pack hotfix unless the specific problem it addresses has been encountered. Service Packs include all of the hotfixes released since the release of the previous Service Pack. The status of hotfix installations is not indicated in the About Windows 2000 dialog box. For more information about Service Packs and hotfixes, see "Additional Resources" at the end of this chapter.

For more troubleshooting information about the 0x50 Stop message, refer to the Microsoft Knowledge Base link , using the keywords winnt and 0x00000050. For information about this resource, see "Additional Resources" at the end of this chapter.

:
:

再精簡一次

Stop Error 0x00000050
Stop error number:

(0x00000050)


Descriptive text:

PAGE_FAULT_IN_NONPAGED_AREA


Usual cause:

Memory error (data cannot be swapped out to disk using the paging file).



To troubleshoot Stop error 0x00000050
=====================================
1. Remove any newly installed hardware (RAM, adapters, hard disks, modems, and so on).
2. Run any system diagnostics supplied by your computer manufacturer, especially the memory check.
3. Verify that any new hardware or software is properly installed. If this is a new installation, contact your hardware or software manufacturer for any Windows 2000 updates or drivers you might need.
4. If the computer is formatted with NTFS, restart your computer, and then run Chkdsk /f /r on the system partition. If you cannot start the system due to the error, use the Command Console and run Chkdsk /r.
5. Disable or uninstall any antivirus programs.
6. Disable BIOS memory options such as caching or shadowing.

>Linux可以安裝於Extended partition所以即使你前面安裝了四個系統於四個主要分割區,Linux應該還是可以架起來的,所以建議Linux最後再裝

我想這樣還是裝不起來，因為extended partition還是會佔掉一個primary partition，也就是說3個primary + 1個extended partition，而extended partition 可以再進一步切割成數個partition。
所以要裝五個OS是可以，不過microsift出的os只能裝在primary上，so.......
如果要裝4個microsoft的os那就會犧牲到其他os，所以倒不如裝3個m牌os，留一個extended裝其他家的os。
剩下的一個os就用VMware來完成囉！
PS:VMware 是pc模擬器，讓你OS裡灌OS。不過效率較差，用來灌WIN98會比較好。

突然想到一點，有可能是你的source有問題，先將其他os拿掉，先灌win2000試試看，等正常後再灌其他os。
切partition時最好使用partition magic，是不是 primary一看就知道，而且還能順便format ntfs、fat。
此外，建議你linux採用 Mandrake 7.2 或 8.0 ，如此一來就可以使用圖形介面的BOOT MANAGER。

幹嘛這麼無聊 ? 一顆 60G 硬碟的成本, 可以買兩個 20G 硬碟了, 你應該買你所需的作業系統數+1的硬碟數, 例如你想安裝5個作業系統, 那就買6個 15~20G 的硬碟, 將一個硬碟裝在 Primary Slave, 當資料硬碟, 並設定為 Fat32. 其餘五個硬碟都設定為 Master 並用抽取軌接到 Primary Master 的位置, 想跑哪個作業系統就插入哪個硬碟. 所有的資料一律都存在資料硬碟, 這樣子任何一個作業系統掛了都可以隨心所欲 format 掉重灌系統, 既不會損失任何資料, 也不會發生5個作業系統需全部重灌的問題.
最重要的, 多重開機是影響系統 performance 的最大元兇, 若要求系統效能要好, 放棄多重開機吧. 再說得實際一點, 這五種作業系統又不能同時在同一台電腦上執行, 何苦將它們擠在一起 ?

1.就你的error message來看,記憶體可能有問題

2.diablo1的意見十分可貴,不過6顆hd???
難道要他update成scsi或換主機板?????

3.不管如何,一顆hd灌5個作業系統是一件很冒險的事
假設你歷經千辛萬苦,已經灌好4個,卻在灌第五個出
事,導致前功盡棄,不是很划不來

4.建議你98me擇一即可,可和xp灌在一起
2000和linux可在一起,為了你好,再買一顆hd吧...

------------------
電腦界的老鳥
音響界的菜鳥

這個主題應發表在七嘴八舌異言堂 ...

[這篇文章曾被 jo jo 重新修正編輯過 (時間 05-03-2001).]